740 8874
254 2827
email:
|
|
| Телефоны в Москве: 740 8874 254 2827 email: |
|
|
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp open |
| 12 | Exposure lamp stays on |
| 12 | Zero cross. Main board or DC power supply |
| 21 | Scan home problem (did not return home) |
| 22 | Scan home problem (did not leave home) |
| 28 | Lens home problem (did not get home) |
| 29 | Lens home problem (did not leave home) |
| 2A | Mirror home problem (did not get home) |
| 2B | Mirror home problem (did not leave home) |
| 40 | Optics thermistor open |
| 52 | Low fuser temperature. Lamp, thermal switch, thermistor |
| 53 | High fuser temperature. Themistor, AC driver, pinched wire |
| 55 | Fuser thermistor open |
| 70 | Waste toner. 80K copies or 9 toner cartridges have been run. Reset with SP mode 83 |
| 96 | Document feeder drive problem |
| U2 | User code. Key counter not installed |
| Код ошибки | Описание |
|---|---|
| E1 | Scanner of Exp. Lamp |
| E2 | Main drive or relay RA2 |
| E3 | Fuser |
| E4 | Total counter |
| U1 | Interlock or thermal fuse |
| U2 | Key counter |
| U3 | Oil (later machines) |
| Код ошибки | Описание |
|---|---|
| E1 | Exposure lamp |
| E2 | Scan problem |
| E5 | Fuser |
| E6 | Drive |
| E7 | Toner waste is full |
| U3 | Developer unit is not installed |
| U5 | Add fuser oil |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp open |
| 12 | Exposure lamp stays on |
| 21 | Scan home problem |
| 22 | Scan home problem(did not return home) |
| 28 | Lens home problem (did not get home) |
| 29 | Lens home problem (did not leave home) |
| 2A | Mirror home problem (did not get home) |
| 2B | Mirror home problem (did not leave home) |
| 40 | Optics thermistor open |
| 52 | Low fuser temperature. Lamp, thermal switch, thermistor |
| 53 | High fuser temperature. Thermistor, AC driver, pinched wire |
| 54 | Fuser low temperature on early EPROM |
| 55 | Fuser thermistor open |
| Код ошибки | Описание |
|---|---|
| E11 | Exposure lamp problem |
| E12 | Exposure lamp problem |
| E13 | Zero cross. Main board or power supply board |
| E14 | Same as E13 |
| E21 | Scan home problem |
| E22 | Scan home problem |
| E28 | Lens home sensor |
| E29 | Lens home problem |
| E2A | 4th & 5th mirror home problem |
| E2B | 4th & 5th mirror home problem. Fuse 2 on AC/DC board |
| E40 | Optics thermistor |
| E42 | Bad transfer corona or HVT |
| E52 | Low fuser temperature |
| E53 | High fuser temperature |
| E54 | Fuser lamp on too long |
| E55 | Fuser thermistor open |
| U1 | Right side open |
| U2 | No key counter |
| U4 | Sorter not latched, not closed |
| U6 | Developer unit not in place |
| Код ошибки | Описание |
|---|---|
| C1 | Front door open |
| C2 | Exit door |
| C3 | Cassette cover |
| C4 | LCT cover |
| C5 | Sorter open or not latched to machine, or fuse 304 on DC power board |
| C6 | ADF cover |
| C7 | Right side cover |
| E101 | Exposure lamp too long |
| E103 | Frequency problem |
| E120, 121 | Scan home problem |
| E124 | Scan drive problem |
| E140 | Lens home, or fuse 303 on DC board |
| E141-143 | Lens home sensor, fuse 303 on DC board |
| E144, 145 | Mirror sensor, fuse 303 on DC board |
| E191 | Image density sensor error |
| E302 | Charge roller problem or HVT problem |
| E346 | Bias loss |
| E351 | Image density sensor problem |
| E352 | TD sensor error |
| E353 | Vsp problem. Dirty or bad image density sensor |
| E354 | Vsg problem. Same as E353 |
| E355 | Toner density sensor problem |
| E356 | Same as 355 |
| E405 | Transfer belt or charge roller drive |
| E440 | Main drive |
| E442 | Drum charge thermistor |
| E501 | Upper lift motor |
| E502 | Lower lift motor |
| E503 | 1st tray motor |
| E504 | 2nd tray motor |
| E505 | 3rd tray motor |
| E506 | Tray main motor drive problem |
| E507 | LCTl lift motor |
| E522-525 | Jogger sensor |
| E541 | Fuser thermistor |
| E542 | Fuser temperature too low |
| E543 | Fuser temperature too high |
| E544 | Fuser temperature too high |
| E547 | Fuser lamp won't shut off |
| E548 | Fuser temperature too high or too low |
| E620 | Communication problem between main board and ARDF |
| E621 | Communication problem between main board and sorter |
| E623 | Communication problem between main board and paper trays |
| E720 | Sorter stapler timing roller sensor |
| E721 | Sorter stapler bin lift sensor |
| E722 | Sorter stapler jogger sensor |
| E723 | Sorter stapler grip sensor |
| E724 | Sorter stapler error |
| E900, 901 | Copy counter |
| U2 | Key counter |
| U6 | Fuser unit not installed properly |
| U7 | Duplex unit |
| Код ошибки | Описание |
|---|---|
| E1 | Exposure lamp |
| E2 | Lamp relay |
| E3 | Registration start switch |
| E4 | Scan not home |
| E5 | No home position |
| E6 | lens home switch not on |
| E7 | Lens home switch off |
| E8, E9 | Encoder |
| EA | Thermofuse |
| Eb | Thermistor |
| EC | Not ready |
| Ed | Pulse generator |
| EE | Total counter |
| EF | Optics |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Lamp relay |
| 20 | Low frequency encoder output |
| 21 | Scan |
| 23 | No registration start signal |
| 24 | No home position |
| 28 | Lens home position not on |
| 29 | Lens home position not off |
| 52 | Thermofuse |
| 53 | Thermistor |
| 54 | Not ready |
| 61 | Pulse generator |
| 91 | Total counter |
| 93 | Interface |
| Код ошибки | Описание |
|---|---|
| E11 | Exposure lamp problem |
| E12 | Exposure lamp problem |
| E13 | Zero cross |
| E21, 22 | Scan home problem. Fuse 102 on DC power supply |
| E28, 29 | Lens home problem |
| E2A | 4th & 5th mirror home problem. Fuse 101 on DC power supply |
| E2B | 4th & 5th mirror home problem |
| E52 | Low fuser temperature |
| E53 | High fuser temperature |
| E55 | Fuser thermistor open |
| E70 | Waste toner full |
| E80 | Communication problem between copier and duplex unit. Fuse 100 or 101 on DC power supply bored |
| E82, 83 | Jogger home problem |
| U1 | Right side open |
| U2 | No key counter |
| U4 | Sorter not latched or not closed |
| U5 | Cassette lift sensor |
| U7 | Duplex open |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Exposure lamp stays on |
| 21, 22 | Scan not home |
| 23 | No signal from registration switch |
| 24 | Scan not home |
| 25 | Scan |
| 28 | Lens not home |
| 29 | Lens won't leave home |
| 2A | Second scan sensor |
| 2A | Mirror sensor stays actuated |
| 2B | Mirror sensor stays actuated |
| 2B | Scan sensor |
| 2C | Scanner moving too fast |
| 2D | Scanner moving too slowly or not moving |
| 31 | Drum thermistor |
| 32 | Toner sensor |
| 41 | Third cassette lift motor sensor |
| 52 | Fuser thermofuse |
| 53 | Fuser thermistor |
| 54 | Low temperature at warm up |
| 55 | High temperature at warm up |
| 56 | Low temperature after warm up |
| 61 | Pulse generator |
| 81, 82 | Duplex jogger |
| 82 | Duplex jogger |
| 91 | Counter |
| 93 | Main board |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 21 | Scan not home |
| 23 | No signal from regulator switch |
| 24 | Scan not home |
| 28 | Lens not home |
| 29 | Lens won't leave home |
| 2A | Second scan flasher |
| 2B | Scan sensor |
| 2C | Scanner moving too fast |
| 2D | Scanner moving too slowly |
| 31 | Drum thermistor |
| 32 | Toner sensor |
| 41 | Third cassette lift motor sensor |
| 53 | Fuser thermistor |
| 54 | Low temperature at warm up |
| 55 | High temperature at warm up |
| 56 | Low temperature after warm up |
| 61 | Pulse generator |
| 91 | Counter |
| 93 | Main board |
| Код ошибки | Описание |
|---|---|
| E1 | Exposure lamp |
| E2 | Lamp relay |
| E3 | Registration start switch |
| E4 | Scan not home |
| E5 | No home position |
| E6 | lens home switch not on |
| E7 | Lens home switch off |
| E8, E9 | Encoder |
| EA | Thermofuse |
| Eb | Thermistor |
| EC | Not ready |
| Ed | Pulse generator |
| EE | Total counter |
| EF | Optics |
| Код ошибки | Описание |
|---|---|
| 21, 22 | Scanner home position error |
| 28, 29 | Lens home position error |
| 2A, 2B | 4th/5th mirror home position error |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 21 | Scan not home |
| 23 | No signal from regulator switch |
| 24 | Scan not home |
| 28 | Lens not home |
| 29 | Lens won't leave home |
| 2A | Second scan flasher |
| 2B | Scan sensor |
| 2C | Scanner moving too fast |
| 2D | Scanner moving too slowly |
| 31 | Drum thermistor |
| 32 | Toner sensor |
| 41 | Third cassette lift motor sensor |
| 53 | Fuser thermistor |
| 54 | Low temperature at warm up |
| 55 | High temperature at warm up |
| 56 | Low temperature after warm up |
| 61 | Pulse generator |
| 91 | Counter |
| 93 | Main board |
| Код ошибки | Описание |
|---|---|
| C1 | Front door open |
| C2 | Exit door |
| C3 | Cassette cover |
| C4 | LCT cover |
| C5 | Sorter open or not latched to machine, or fuse 304 on DC power board |
| C6 | ADF cover |
| C7 | Right side cover |
| E101 | Exposure lamp too long |
| E103 | Frequency problem |
| E120, 121 | Scan home problem |
| E124 | Scan drive problem |
| E140-143 | Lens home, or fuse 303 on DC board |
| E144, 145 | Mirror sensor, fuse 303 on DC board |
| E191 | Image density sensor error |
| E302 | Charge roller problem or HVT problem |
| E346 | Bias loss |
| E351 | Image density sensor problem |
| E352 | TD sensor error |
| E353, 354 | Vsp problem. Dirty or bad image density sensor |
| E355, 356 | Toner density sensor problem |
| E405 | Transfer belt or charge roller drive |
| E440 | Main drive |
| E442 | Drum charge thermistor |
| E501 | Upper lift motor |
| E502 | Lower lift motor |
| E503 | 1st tray motor |
| E504 | 2nd tray motor |
| E505 | 3rd tray motor |
| E506 | Tray main motor drive problem |
| E507 | LCTl lift motor |
| E522-525 | Jogger sensor |
| E541 | Fuser thermistor |
| E542 | Fuser temperature too low |
| E543 | Fuser temperature too high |
| E544 | Fuser temperature too high |
| E547 | Fuser lamp won't shut off |
| E548 | Fuser temperature too high or too low |
| E620 | Communication problem between main board and ARDF |
| E621 | Communication problem between main board and sorter |
| E623 | Communication problem between main board and paper trays |
| E720 | Sorter stapler timing roller sensor |
| E721 | Sorter stapler bin lift sensor |
| E722 | Sorter stapler jogger sensor |
| E723 | Sorter stapler grip sensor |
| E724 | Sorter stapler error |
| E900, 901 | Copy counter |
| U2 | Key counter |
| U6 | Fuser unit not installed properly |
| U7 | Duplex unit |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Exposure lamp relay |
| 21-24 | Scan |
| 25 | Scan motor |
| 28 | Lens position |
| 2A, 2B | 2nd scan home |
| 2C, 2D | Scan motor |
| 2E | Encoder |
| 31 | Drum thermistor |
| 43 | Lower paper feed |
| 52 | Thermofuse |
| 53 | Thermistor |
| 54 | No heat |
| 55 | Overheat |
| 61 | Drive system |
| 81, 82 | Jogger problem |
| 91 | Counter |
| 93 | Optics and main board interface |
| 94 | Optics board and main board interface |
| Код ошибки | Описание |
|---|---|
| C1 | Front door open |
| C2 | Exit door |
| C3 | Cassette cover |
| C4 | LCT cover |
| C5 | Sorter open or not latched to machine, or fuse 304 on DC power board |
| C6 | ADF cover |
| C7 | Right side cover |
| E101 | Exposure lamp on too long |
| E103 | Frequency problem |
| E120, 121 | Scan home problem |
| E124 | Scan drive problem |
| E140-143 | Lens home, or fuse 303 on DC board |
| E144, 145 | Mirror sensor, fuse 303 on DC board |
| E191 | Image density sensor problem |
| E302 | Charge roller problem or HVT problem |
| E346 | Bias loss |
| E351 | Image density sensor error |
| E352 | TD sensor error |
| E353, 354 | Vsp problem. Dirty or bad image density sensor |
| E355 | Toner density sensor problem |
| E356 | Vsp problem. Dirty or bad image density sensor |
| E405 | Transfer belt or charge roller drive |
| E440 | Main drive |
| E442 | Drum charge thermistor |
| E501 | Upper lift motor |
| E502 | Lower lift motor |
| E503 | 1st tray motor |
| E504 | 2nd tray motor |
| E505 | 3rd tray motor |
| E506 | Tray main motor drive problem |
| E507 | LCT lift motor |
| E522-525 | Jogger sensor |
| E541 | Fuser thermistor |
| E542 | Fuser temperature too low |
| E543 | Fuser temperature too high |
| E544 | Fuser temperature too high |
| E547 | Fuser lamp won't shut off |
| E548 | Fuser temperature too high or too low |
| E620 | Communication problem between main board and ARDF |
| E621 | Communication problem between main board and sorter |
| E623 | Communication problem between main board and paper trays |
| E720 | Sorter stapler timing roller sensor |
| E721 | Sorter stapler bin lift sensor |
| E722 | Sorter stapler jogger sensor |
| E723 | Sorter stapler grip sensor |
| E724 | Sorter stapler error |
| E900, 901 | Copy counter |
| U2 | Key counter |
| U6 | Fuser unit not installed properly |
| U7 | Duplex unit |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Exposure lamp relay |
| 21-24 | Scan |
| 28 | Lens position |
| 29 | Lens |
| 2A-2D | Scan |
| 41 | Upper paper feed |
| 43 | Lower paper feed |
| 52 | Thermofuse |
| 53 | Thermistor |
| 54 | No heat |
| 61 | Drive |
| 81 | Jogger |
| 91 | Counter |
| 93 | Main board or optics |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Exposure lamp stays on |
| 21 | Scan not home |
| 22 | Scan not home |
| 23 | So signal from registration switch |
| 24 | Scan not home |
| 25 | Scan |
| 28 | Lens not home |
| 29 | Lens won't leave home |
| 2A | Second scan sensor |
| 2A | Mirror sensor stays actuated |
| 2B | Mirror sensor stays actuated |
| 2B | Scan sensor |
| 2C | Scanner moving to fast |
| 2D | Scanner moving too slowly or not moving |
| 31 | Drum thermistor |
| 32 | Toner sensor |
| 41 | Third cassette lift motor sensor |
| 52 | Fuser thermofuse |
| 53 | Fuser thermistor |
| 54 | Low temperature at warm up |
| 55 | High temperature at warm up |
| 56 | Low temperature after warm up |
| 61 | Pulse generator |
| 81 | Duplex jogger |
| 82 | Duplex jogger |
| 91 | Counter |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | ExpExposure lamp relay |
| 21 | Scan home switch not actuated |
| 22 | Scan home switch activated |
| 23 | Scan registration switch |
| 24 | Scan home problem |
| 25 | Scan motor |
| 28 | Lens home switch not actuated |
| 29 | Lens home switch actuated |
| 2A | 2nd scan home switch not actuated |
| 2b | 2nd home scan switch actuated |
| 2c | Encoder (high frequency) |
| 2d | Encoder (low frequency) |
| 2E | No encoder |
| 31 | Drum thermistor |
| 52 | Fuser thermofuse (or F3) |
| 53 | Fuser thermistor |
| 54 | No ready |
| 55 | High temperature |
| 61 | Pulse generator |
| 81 | Jogger home switch not actuated |
| 82 | Jogger home switch actuated |
| 91 | Total counter |
| 94 | Data transfer problem between main board and operations board |
| Код ошибки | Описание |
|---|---|
| C1 | Front door open |
| C2 | Exit door |
| C3 | Cassette cover |
| C4 | LCT cover |
| C5 | Sorter open/not latched to machine |
| C6 | ADF cover |
| C7 | Right side cover |
| E101 | Exposure lamp on too long |
| E103 | Frequency problem |
| E120, 121 | Scan home problem |
| E124 | Scan drive problem |
| E140-143 | Lens home, or fuse 303 on DC board |
| E144, 145 | Mirror sensor, fuse 303 on DC board |
| E191 | Image density sensor problem |
| E302 | Charge roller or HVT problem |
| E346 | Bias loss |
| E351 | Image density sensor problem |
| E352 | TD sensor error |
| E353, 354 | Vsp problem |
| E355, 356 | Toner density sensor problem |
| E405 | Transfer belt or charge roller drive |
| E440 | Main drive |
| E442 | Drum charge thermistor |
| E501 | Upper lift motor |
| E502 | lower lift motor |
| E503 | 1st tray motor |
| E504 | 2nd tray motor |
| E505 | 3rd tray motor |
| E506 | Tray main motor drive problem |
| E507 | LCT lift motor |
| E522-525 | Jogger sensor |
| E541 | Fuser thermistor |
| E542 | Fuser temperature too low |
| E543 | Fuser temperature too high |
| E544 | Fuser temperature too high |
| E547 | Fuser lamp won't shut off |
| E548 | Fuser temperature too high or too low |
| E620 | Communication problem between main board and ARDF |
| E621 | Communication problem between main board and sorter |
| E623 | Communication problem between main board and paper trays |
| E720 | Sorter stapler timing roller sensor |
| E721 | Sorter stapler bin lift sensor |
| E722 | Sorter stapler jogger sensor |
| E723 | Sorter stapler grip sensor |
| E724 | Sorter stapler error |
| E900, 901 | Copy counter |
| U2 | Key counter |
| U6 | Fuser unit not installed properly |
| U7 | Duplex unit |
| Код ошибки | Описание |
|---|---|
| 1 | Exposure lamp |
| 10 | Scanner velocity |
| 11 | Scanner return |
| 12 | Total counter |
| 13 | Corona problem |
| 2 | Drum thermistor |
| 3 | Drum heater |
| 4 | Drum overheat |
| 5 | Fuser thermistor |
| 6 | Fuser lamp |
| 7 | Fuser overheat |
| 8 | Optics encoder |
| 9 | Scanner home |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 12 | Exposure lamp stays on |
| 21, 22 | Scan not home |
| 23 | So signal from registration switch |
| 24 | Scan not home |
| 25 | Scan |
| 28 | Lens not home |
| 29 | Lens won't leave home |
| 2A | Second scan sensor |
| 2A | Mirror sensor stays actuated |
| 2B | Scan sensor |
| 2C | Scanner moving to fast |
| 2D | Scanner moving too slowly or not moving |
| 31 | Drum thermistor |
| 32 | Toner sensor |
| 41 | Third cassette lift motor sensor |
| 52 | Fuser thermofuse |
| 53 | Fuser thermistor |
| 54 | Low temperature at warm up |
| 55 | High temperature at warm up |
| 56 | Low temperature after warm up |
| 61 | Pulse generator |
| 81, 82 | Duplex jogger |
| 91 | Counter |
| 93 | Main board |
| Код ошибки | Описание |
|---|---|
| 101 | Exposure lamp |
| 103 | Power frequency problem |
| 104 | Exposure lamp |
| 120 | Scanner home problem |
| 121 | Scan home problem |
| 125 | Scanning too slow |
| 126 | Scanning too fast |
| 127 | Scan drive problem or encoder |
| 140 | Lens home problem (vertical) |
| 141 | Lens home problem (vertical) |
| 142 | Lens home problem (horizontal) |
| 143 | Lens home problem (horizontal) |
| 144 | 3rd scan sensor problem |
| 145 | 3rd scan sensor problem |
| 146 | Magnification problem |
| 190 | Optics thermistor open circuit |
| 191 | Scan motor thermistor |
| 302 | Charge corona short |
| 303 | Charge corona cleaner problem |
| 341 | Developer motor drive problem |
| 342 | Toner disposal motor drive problem |
| 343 | Vsp. Problem. Image density sensor problem |
| 351 | Vsg. Problem. Higher than 4.3 volts. Image density sensor problem |
| 352 | Toner sensor problem during developer calibration |
| 353 | Vsp Problem. Image density sensor, drum bias or HVT |
| 354 | Vsg Problem. Image density sensor, drum bias or HVT |
| 355 | Toner density sensor problem. Vtd problem. Undertoned |
| 356 | Toner density sensor problem. Vtd problem. Overtoned |
| 357 | Vsp problem. Image density sensor, drum |
| 358 | Vsp problem. Image density sensor, drum, toner dust |
| 361 | Drum potential sensor calibration during process control setup |
| 364 | Vd problem. Drum potential sensor, drum or charge corona |
| 365 | V1 problem. Drum potential sensor, drum, charge corona, dirty optics |
| 402 | Transfer, transfer belt, HVT |
| 440 | Main motor speed problem |
| 442 | Drum thermistor |
| 500 | Bypass feed |
| 501 | Paper feed motor |
| 502 | 1st lift motor |
| 503 | 2nd lift motor |
| 504 | 3rd lift motor |
| 506 | LCT motor |
| 507 | LCT feed motor |
| 508 | Tandem fence motor |
| 510 | Tandem side home sensor |
| 511 | Tandem side home sensor |
| 520 | Duplex/fuser drive motor problem |
| 522 | Jogger home sensor |
| 523 | Jogger home sensor |
| 541 | Fuser thermistor |
| 542 | Fuser does not warm-up |
| 543 | Fuser temperature too high. Monitored by main board |
| 544 | Fuser temperature too high. Monitored by optics board |
| 545 | Low fuser temperature. Monitored by main board |
| 546 | Low fuser temperature. Monitored by optics board |
| 547 | Fuser lamp won't shut off |
| 548 | Erratic fuser temperature |
| 600 | Communication problem between main board and operation board |
| 601 | Communication problem between main board and optics board |
| 602 | Communication problem between main board and high voltage unit |
| 603 | Main board problem |
| 620 | Communication problem between main board and document feeder boards |
| 621 | Communication problem between main board and sorter staplers or finisher |
| 700 | DJF/RDH feed motor |
| 701 | DJF/RDH transport belt problem |
| 702 | DJF exit or RDH inverter motor |
| 703 | RDH exit motor problem |
| 730 | Sorter/stapler or finisher transport motor |
| 731 | Bin lift motor |
| 732 | Tray shift motor |
| 733 | Tray shift lift motor |
| 735 | Duplex jogger motor |
| 737 | Gripper motor |
| 738 | Staple motor |
| 740 | Staple drive motor |
| 741 | Bin rear plate motor (stapler) |
| 742 | Finisher stack feed motor |
| 900 | Total counter |
| 901 | Total counter |
| SC | Full waste toner bottle. Technician must empty this. Emptying the waste toner and reinstalling the bottle will clear this code |
| Код ошибки | Описание |
|---|---|
| 11 | Exposure lamp |
| 13 | Exposure lamp |
| 14 | Electrical frequency problem |
| 21, 22 | Scan problem |
| 24 | Scan home problem |
| 25 | Scan drive motor problem |
| 26 | Scan problem during simulation V1 adjustment (SP mode 67) |
| 27 | Scan problem during simulation |
| 28, 29 | Lens home problem |
| 2A, 2B | Mirror home sensor |
| 2D | Scan drive problem or fuse 5 on optics board |
| 31 | Drum thermistor |
| 41 | Tray lift |
| 42 | 2nd tray lift |
| 43 | 3rd tray lift |
| 53 | Fuser thermistor problem |
| 54 | Fuse temperature low |
| 55 | Fuser temperature too high |
| 56 | Fuser temperature low |
| 57 | Fuser lamp on too long |
| 58 | Fuser temperature erratic |
| 61 | Main drive problem, or fuse 1 or fuse 6 on main motor board |
| 62 | Developer drive problem, or fuse 1 on developer motor drive board |
| 81, 82 | Duplex jogger home sensor |
| 85, 86 | Charge corona cleaner problem |
| 87 | Transfer/separator corona cleaner unit not working |
| 88 | Transfer/separator corona cleaner unit not home |
| 91 | Total counter |
| B1 | Sorter shift tray |
| B2 | Sorter shift motor |
| B3 | Sorter shift tray up/down motor |
| B4 | Stapler transport motor |
| B5 | Stapler lift motor |
| B6 | Stapler drive motor |
| B7 | Stapler jogger motor |
| B8 | Stapler motor |
| Код ошибки | Описание |
|---|---|
| E1 | Exposure lamp |
| E2 | Scan |
| E5 | Fuser |
| E6 | Drive |
| E7 | Master not turning |
| E8 | Lamp heater (exposure) |
| Код ошибки | Описание |
|---|---|
| C2 | Drive problem |
| C3 | Scan problem |
| C4 | Lens problem |
| C5 | Coronas |
| C6 | Heater problem or only 1 of the 2 front door interlocks switches is actuated |
| CO | Main board problem Run simulation 90. Try power off/on |
