Телефоны в Москве:
740 8874
254 2827

email:

feed_id: 3279 pattern_id: 5 limit: image_type: search: search: %referrer% search: %title%

Коды ошибок копиров Ricoh. Дубликаторы

Ricoh Priport VT-2100/2130/2150/2300/2500

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in cutter section: The cutter motor does not reach both right and left cutter position detecting switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor is not turned off even though the paper table UP or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 03	Malfunction in the program	1) PROM defective 2) Control PCB defective
E 04	Temperature of the thermal head or the power supply unit is high: Temperature of the thermal head becomes greater than 57^°C or the temperature of the power supply unit becomes greater than 85^°C when the machine is in stand-by condition	1) Thermistor defective 2) Thermal head defective 3) Power supply unit defective
E 05	Malfunction in the image shifting section	1) Encoder connector of the image shifting section disconnected 2) Encoder defective
E 06	Mechanical lock: When a paper jam or part failure occurs, the decoder detects that the motor speed is incorrect if this occurs, the main motor turns off. This prevents any further damage its components or fuse failure	1) Paper Jam 2) Parts failure
E 07	Malfunction in the program (PROM). When using I/O check mode, "E07" lights up if the ROM is defective. NOTE: When "E03" is lit, check whether or not the PROM is defective using I/O check mode	ROM defective
E 08	The pulse width applied to the thermal head is out of standard	Thermal head drive board detective
E 08	The power supply unit temperature reaches 85^°C	Power supply unit detective (Thermal guard failure)

Ricoh Priport VT-2200

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in the cutter section: The cutter does not reach both right and left cutter position switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor status does not change even though the paper table Up or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 04	The temperature of the thermal head or the power supply unit is high: The temperature of the thermal head becomes greater than 53^°C	1) Defective thermistor 2) Defective thermal head 3) Defective power supply unit
E 05	Malfunction in the image shifting section: All the encoder output signals are at the "H" level	1) Encoder connector of the image shifting section is disconnected 2) Defective encoder
E 06	Mechanical lock: The drum rotation sensor detects that the drum rotation speed is abnormal	1) Mechanical lock 2) Main motor failure
E 09	Malfunction of the thermal head	1) Defective thermal head 2) Defective thermistor 3) Thermal head harness broken
E 10	Malfunction in the thermal head drive section	1) Defective main control PCB 2) Thermal head drive wire short circuit
E 11	Image shift motor malfunction: The encoder status does not change within 3 seconds after the encoder motor starts rotating	1) Image shift motor lock 2) Image shift motor harness broken
E 12	Malfunction in the pressure plate drive section: The loner pressure plate sensor is not actuated within 8 seconds. The upper pressure plate sensor is not actuated within 4 seconds	1) Pressure plate motor lock 2) Pressure plate motor harness broken 3) Pressure plate position sensor malfunction

Ricoh Priport VT-2250 (C226)

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in the cutter section: The cutter does not reach both right and left cutter position switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor status does not change even though the paper table Up or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 04	The temperature of the thermal head is high: The temperature of the thermal head becomes greater than 54^°C	1) Defective thermistor 2) Defective thermal head
E 05	Malfunction in the image shifting section: All the encoder output signals are at the "H" level	1) Encoder connector of the image shifting section is disconnected 2) Defective encoder
E 06	Mechanical lock: The drum rotation sensor detects that the drum rotation speed is abnormal	1) Mechanical lock 2) Main motor failure 3) Blown fuse on the AC drive board
E 09	Malfunction of the thermal head	1) Defective thermal head 2) Defective thermistor 3) Thermal head harness broken
E 10	Malfunction in the thermal head drive section	1) Defective main control PCB 2) Thermal head drive wire short circuit
E 11	Image shift motor malfunction: The encoder status does not change within 3 seconds after the encoder motor starts rotating	1) Image shift motor lock 2) Image shift motor harness broken
E 12	Malfunction in the pressure plate drive section: The upper or lower pressure plate sensor remains activated for more than 4 seconds after the pressure plate motor starts turning. The upper or lower pressure plate sensor is not activated within 8 seconds after the pressure plate starts leaving for the other side	1) Pressure plate motor lock 2) Pressure plate motor harness broken 3) Pressure plate sensor malfunction
E 13	Scanner malfunction: The scanner home position sensor did not turn on after the motor moved for more than 7 seconds back to the home position after scanning. The scanner could not leave the home position within 4 seconds of power on. Otherwise, when the scanner could not return to the home position within 2 seconds of leaving	1) Mechanical lock of scanner 2) Defective scanner home position sensor

Ricoh Priport VT-2250 (C224)

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in the cutter section: The cutter does not reach both right and left cutter position switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor status does not change even though the paper table Up or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 04	The temperature of the thermal head or the power supply unit is high: The temperature of the thermal head becomes greater than 53^°C	1) Defective thermistor 2) Defective thermal head 3) Defective power supply unit
E 05	Malfunction in the image shifting section: All the encoder output signals are at the "H" level	1) Encoder connector of the image shifting section is disconnected 2) Defective encoder
E 06	Mechanical lock: The drum rotation sensor detects that the drum rotation speed is abnormal	1) Mechanical lock 2) Main motor failure
E 09	Malfunction of the thermal head	1) Defective thermal head 2) Defective thermistor 3) Thermal head harness broken
E 10	Malfunction in the thermal head drive section	1) Defective main control PCB 2) Thermal head drive wire short circuit
E 11	Image shift motor malfunction: The encoder status does not change within 3 seconds after the encoder motor starts rotating	1) Image shift motor lock 2) Image shift motor harness broken
E 12	Malfunction in the pressure plate drive section: The loner pressure plate sensor is not actuated within 8 seconds. The upper pressure plate sensor is not actuated within 4 seconds	1) Pressure plate motor lock 2) Pressure plate motor harness broken 3) Pressure plate position sensor malfunction

Ricoh Priport VT-2250 (C215/C216)

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in cutter section: The cutter does not reach both right and left cutter position switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor status does not change even though the paper table UP or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 03	Malfunction in the program	1) Defective PROM 2) Defective control PCB
E 04	Temperature of the thermal head or the power supply unit is high: Temperature of the thermal head becomes greater than 57^°C or the temperature of the power supply unit becomes greater than 85^°C when the machine is in stand-by condition	1) Defective thermistor 2) Defective thermal head 3) Defective power supply unit
E 05	Malfunction in the image shifting section	1) Encoder connector of the image shifting sectiond is connected 2) Defective encoder
E 06	Mechanical lock: Drum rotation sensor detects that the drum rotation speed is abnormal	1) Mechanical lock 2) Main motor failure
E 07	Malfunction in the program (PROM). When using I/O check mode, "E 07" lights up if the ROM is defective. NOTE: When "E 03" is lit, access I/O check mode to check if the PROM is defective	Defective ROM
E 08	Thermal head drive signal (ENL) is defective	Defective image processing board

Ricoh Priport VT-2250 (C211/C212/C213)

Код ошибки	Неисправность	Возможные причины
E 01	Malfunction in cutter section: The cutter motor does not reach both right and left cutter position detecting switches within 2 seconds	1) Drive wire cut 2) Drive section malfunction 3) No power supply
E 02	Malfunction in the paper table drive section: The lower limit sensor or the paper table height sensor is not turned off even though the paper table UP or Down signal is applied	1) Drive worm gear broken 2) Mounting screw of the worm gear broken 3) No power supply
E 03	Malfunction in the program	1) PROM defective 2) Control PCB defective
E 04	Temperature of the thermal head or the power supply unit is high: Temperature of the thermal head becomes greater than 57^°C or the temperature of the power supply unit becomes greater than 85^°C when the machine is in stand-by condition	1) Thermistor defective 2) Thermal head defective 3) Power supply unit defective
E 05	Malfunction in the image shifting section	1) Encoder connector of the image shifting section disconnected 2) Encoder defective
E 06	Mechanical lock: When a paper jam or part failure occurs, the decoder detects that the motor speed is incorrect if this occurs, the main motor turns off. This prevents any further damage its components or fuse failure	1) Paper Jam 2) Parts failure
E 07	Malfunction in the program (PROM). When using I/O check mode, "E07" lights up if the ROM is defective. NOTE: When "E03" is lit, check whether or not the PROM is defective using I/O check mode	ROM defective
E 08	The pulse width applied to the thermal head is out of standard Thermal head drive board detective. The power supply unit temperature reaches 85^°C	Power supply unit detective (Thermal guard failure)

Ricoh Priport JP-5500

Код	Описание
SC01-00	Ошибка энергонезависимой ОЗУ платы MPU
SC01-01	Ошибка флэш-ПЗУ платы MPU
SC02-00	Заклинивание двигателя привода сканера
SC03-00	Ошибка ID-сигнала термоголовки
SC03-01	Ошибка имнульсов управления энергией термоголовки
SC03-02	Короткое замыкание в термисторе термоголовки
SC03-03	Ненормальная температура термоголовки
SC04-00	Ошибка датчика исходного положения ножа обрезки мастер-пленки
SC04-10	Ошибка датчика положения прижимного вала термоголовки
SC04-11	Ошибка датчика положения прижимного вала термоголовки
SC04-20	Ошибка обрезки мастер-пленки
SC05-00	Заклинивание главного двигателя
SC05-01	Заклинивание главного двигателя
SC05-10	Ошибка датчика исходного положения перемещения изображения
SC05-12	Отсутствуют импульсы инкодера положения изображения
SC05-20	Ошибка датчика исходного положения раскатного барабана
SC05-21	Ошибка датчика исходного положения раскатного барабана
SC05-22	Отсутствуют импульсы датчика смещения раскатного барабана
SC05-30	Обрыв в термисторе раскатного барабана
SC05-31	Короткое замыкание в термисторе раскатного барабана
SC05-32	Ошибка датчика насоса подачи краски
SC05-33	Ошибка датчика насоса подачи краски
SC05-40	Ошибка датчика эксцентрика A4
SC05-41	Ошибка датчика эксцентрика A3
SC05-50	Ошибка датчика закрытия фиксатора мастер-пленки на барабане
SC05-51	Ошибка датчика открытия фиксатора мастер-пленки на барабане
SC05-60	Ошибка датчика исходного положения вала подготовки барабана
SC06-00	Ошибка планки прессования отработанных кадров мастер-пленки
SC07-00	Ошибка датчика 0,1,2 или 3 платы детектирования прижима подачи
SC07-10	Ошибка датчика 0,1,2 или 3 платы детектирования сепарации
SC07-20	Ошибка инкодера подачи
SC07-21	Ошибка датчика старта лотка подачи бумаги
SC07-22	Ошибка датчика старта лотка подачи бумаги
SC07-30	Ошибка двигателя пластины сепарации
SC07-50	Ошибка датчика положения выходных направляющих плоскостей
SC07-51	Ошибка датчика положения выходных направляющих плоскостей
SC07-60	Ошибка датчика бумаги разделителя тиражей
SC07-61	Ошибка датчика положения разделителя тиражей
SC07-70	Ошибка датчика исходного положения слайдера
SC07-72	Ошибка датчика исходного положения слайдера
SC20-00	Ошибка опционной платы памяти (опция редактирования)
SC21-00	Ошибка микросхемы ASIC управления памятью
SC22-00	Ошибка ОЗУ узоров заливки
SC30-00	Ошибка датчика крайнего нижнего положения лотка подачи бумаги
SC30-01	Ошибка датчика крайнего верхнего положения лотка подачи бумаги
SC30-02	Ошибка датчика крайнего верхнего положения лотка подачи бумаги
SC30-03	Ошибка датчика крайнего верхнего положения лотка подачи бумаги
SC31-40	Ошибка датчика крайнего верхнего положения лотка подачи бумаги
SC80-00	Ошибка сигнала интерфейса подключения ПК